Me watching the Internet fall apart this week
@scalzi Gemini capsules are cute actually as far as I am concerned.
@scalzi I've already been buying some ISA modems to get ready for setting one up
@evermorian @scalzi fortunately my sister is a phone nerd so I have landlines to spare. I'm gonna have as many nodes on my BBS as I can scrounge up working modems!
i'm thinking of getting my ham license and getting into packet radio
@Perrin42 @clive @scalzi @W6KME I have run a BBS, I have written BBS software, I made some (small change) writing BBS extensions, and have a lot of packet radio equipment (not in use, lol) here. Did you know most of the ham packet radio stuff is E,7,1, for some unfathomable reason?!?! (at least, my stuff all defaults to E,7,1). I mean, in my Hayes modem days everything was N,8,1. Unless you were connecting to some ancient mainframe on E,7,1.
Hollerith cards are twelve bits by eighty columns.
IBM used a six bit code for data from them.
I've never had anything to do with IBM gear beyond the 029 card-punch.
Baudot teleprinters used a 5 bit code with shift characters to give 62 different characters.
@zl2tod @paul_ipv6 @ai6yr @Perrin42 @clive @scalzi @W6KME I only worked on Singer Business Machines mini computers. 5-bit internal, boot via card deck or disk drive from the terminal ( 90V diode logic, all white wire harness). They would upload data via a synch network adapter to an IBM 360.
The os was macro2, built on said IBM. It came on a 14inch 5MB disk pack (had to do head alignment on those to get a decent cat eye). 33ms hard wired partition switch. First alu I remember. Took a 19" rack, as did the disk partition. Could tweak the memory for i/o via jumpers on the edge of serial board. The thing out performed 8080's when doing i/o to pos terminals 200 in under 11 seconds with minimal droppage, almost none (dependant on total data content).
The structure of the Singer System Ten reminds me of the old electro-mechanical accounting machines.
The first disk drive I saw was attached to an NCR model 43. It was a half inch thick disk of rust covered aluminium born between two similar plates which each had about ten 1/4" tape heads in cylindrical bodies poked through holes skimming the surface. It could store a very small amount of data and there was no CPU involved.
@clive @zl2tod @paul_ipv6 @ai6yr @Perrin42 @scalzi @W6KME i had to pick up Friden rotary calcs to bring them in for service. Only one person was trained on them - 3000 parts (as i recall) only ran in one direction, if every thing worked properly after servicing, a entry sequence would put the calc in a mode that would play "the Friden march".
One lady at the bank I returned hers, told me that even with the computers, they could only close the books for the year once she verified the numbers using the calculator.
Fwiw - finance people are really into places to the right of the decimal point. On dec pdp-11s, RSTS/E, for science, building BASIC with two-word math was all that's needed. For business, four-word math was required.
My first job out of school was fixing NCR cash registers.
Training would be overstating it: one was told to take it apart and reassemble it and left to it. There was no march.
Many of the tools were bicycle spokes: spring hooks; timing bars inserted through holes in the mechanism to line everything up before joining modules.
@zl2tod @clive @paul_ipv6 @ai6yr @Perrin42 @scalzi @W6KME My first tech job was making printing calcs and pos registers. Learned how to "bend" the print arm so the rotary print wheel would hit the print roller at 90 degrees. The keyboard was a series of shutters where in one end was a lamp and parabolic mirror and the other end was a set of photo diodes. Had to deal with bad vendor shift registers because I and the testers could over run the shift register doing data entry during testing.
On a later model (925?) we had fun sorting through bad lots of SSRs and 555 timers, all found during final QA or after 96 hr burn-in.
https://vintagepointofsale.com/category/system-manufacturers/singer-friden/
@scalzi i'm on the look out for a cheap one of these